Yamaha V150 Скачать руководство пользователя | Manualshive

Страница: 9 / 82

background image

General information

4

the switch, stopping the engine.

●

Know the marine laws and regulations
where you will be boating—and obey
them. For basic boating rules, see “Rules
of the road” on page 5.

●

Stay informed about the weather. Check
weather forecasts before boating. Avoid
boating in hazardous weather.

●

Tell someone where you are going: leave
a Float Plan with a responsible person. Be
sure to cancel the Float Plan when you re-
turn.

●

Use common sense and good judgment
when boating. Know your abilities, and be
sure you understand how your boat han-
dles under the different boating conditions
you may encounter. Operate within your
limits, and the limits of your boat. Always
operate at safe speeds, and keep a careful
watch for obstacles and other traffic.

●

Always watch carefully for swimmers dur-
ing the engine operation.

●

Stay away from swimming areas.

●

When a swimmer is in the water near you
shift into neutral and shut off the engine.

●

Do not illegally discard empty containers
used to replace or replenish oil. For the
correct processing of empty containers,
consult the dealer where you purchased
the oil.

●

When replacing oils used to lubricate the
product (engine or gear oil), be sure to
wipe away any spilt oil. Never pour oil with-
out using a funnel or similar device. If nec-
essary, verify the necessary replacement
procedure with the dealer.

●

Never illegally discard (dump) the product.
Yamaha recommends consulting the deal-
er on discarding the product.

Be informed about boating safety. Additional
publications and information can be obtained

from many organizations, including the fol-
lowing:

United States Coast Guard

Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Af-
fairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647

National Marine Manufacturers Associa-
tion (NMMA)

401 N. Michigan Ave.
Chicago, Il 60611

Marine Retailers Association of America

155 N. Michigan Ave.
Chicago, Il 60601

EMU25382

Important labels

EMU25395

Warning labels

ZMU03928

ZMU01948

«
...
7
8
9
10
11
...
»

Содержание V150



















































































Отзывы:

Нет отзывов

Похожие инструкции для V150

Бренд: Telit Wireless Solutions Страницы: 5

NCN8024GEVB Series

Бренд: ON Semiconductor Страницы: 5

Бренд: Aeroflex Страницы: 20

EMB-APL1-A10-3350-F1-LV

Бренд: Aaeon Страницы: 42

Бренд: NXP Semiconductors Страницы: 28

Бренд: NXP Semiconductors Страницы: 16

Бренд: Silicon Laboratories Страницы: 16

Бренд: DFI Страницы: 92

Бренд: Advantech Страницы: 98

Бренд: JETWAY Страницы: 48

Бренд: ASROCK Страницы: 162

Бренд: Gigabyte Страницы: 80

NuMicro NuTiny-SDK-NUC505

Бренд: Nuvoton Страницы: 26

PHANTOM GAMING X670E PG Lightning

Бренд: ASROCK Страницы: 66

Бренд: Fujitsu Страницы: 30

Бренд: DFI Страницы: 64

Бренд: IEI Technology Страницы: 161

Бренд: Texas Instruments Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды