Yamaha V150 Скачать руководство пользователя | Manualshive

Страница: 29 / 82

background image

24

Operation

EMU26901

Installation

CAUTION:

ECM00110

Incorrect engine height or obstructions
to smooth water flow (such as the design
or condition of the boat, or accessories
such as transom ladders or depth finder
transducers) can create airborne water
spray while the boat is cruising. Severe
engine damage may result if the motor is
operated continuously in the presence of

airborne water spray.

NOTE:

During water testing check the buoyancy of
the boat, at rest, with its maximum load.
Check that the static water level on the ex-
haust housing is low enough to prevent wa-
ter entry into the powerhead, when water
rises due to waves when the outboard is not

running.

EMU26910

Mounting the outboard motor

WARNING

EWM00820

●

Overpowering a boat could cause se-
vere instability. Do not install an out-
board motor with more horsepower
than the maximum rating on the capac-
ity plate of the boat. If the boat does not
have a capacity plate, consult the boat
manufacturer.

●

The information presented in this sec-
tion is intended as reference only. It is
not possible to provide complete in-
structions for every possible boat and
motor combination. Proper mounting
depends in part on experience and the

specific boat and motor combination.

WARNING

EWM00830

Improper mounting of the outboard mo-
tor could result in hazardous conditions
such as poor handling, loss of control, or
fire hazards. Observe the following:

●

For permanently mounted models, your
dealer or other person experienced in
proper rigging should mount the motor.
If you are mounting the motor yourself,
you should be trained by an experi-
enced person.

●

For portable models, your dealer or oth-
er person experienced in proper out-
board motor mounting should show

you how to mount your motor.

Mount the outboard motor on the center line
(keel line) of the boat, and ensure that the
boat itself is well balanced. Otherwise the
boat will be hard to steer. For boats without
a keel or which are asymmetrical, consult
your dealer.

EMU26930

Mounting height (boat bottom)

To run your boat at optimum efficiency, the
water resistance (drag) of the boat and out-
board motor must be made as little as possi-
ble. The mounting height of the outboard

1. Center line (keel line)

1

ZMU01873

«
...
27
28
29
30
31
...
»

Содержание V150



















































































Отзывы:

Нет отзывов

Похожие инструкции для V150

AP0100CSSL00SPGAH-GEVB

Бренд: ON Semiconductor Страницы: 6

Nucleo STM32F302R8

Бренд: ST Страницы: 18

Бренд: JETWAY Страницы: 48

790XT-G35 series

Бренд: MSI Страницы: 103

Бренд: Microchip Technology Страницы: 34

Coccinella Master Plus

Бренд: SEA Страницы: 2

Бренд: HONDA marine Страницы: 2

WAFER - E668EV ATX

Бренд: IEI Technology Страницы: 59

44011-0208-13-2

Бренд: S&T Страницы: 65

Бренд: JETWAY Страницы: 48

Бренд: IEI Technology Страницы: 53

Бренд: unicore Страницы: 11

Бренд: DFI Страницы: 65

Бренд: DFI Страницы: 73

Бренд: DFI Страницы: 114

Бренд: DFI Страницы: 122

Бренд: IEI Technology Страницы: 161

Бренд: Huawei Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды