Yamaha PM1D Manager V2 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 56

background image

Surround panning

41

■

SELECTED INPUT CHANNEL block

In the SELECTED INPUT CHANNEL block MIX SEND section, the illumination of MIX SEND [NAME] indicators 17–
24 and the movement of MIX SEND [LEVEL/PAN] encoders 17–24 will change as follows, according to the currently
selected surround mode.

1

L< >R

This encoder functions as a controller that moves the
surround pan of the currently selected channel
between left and right.

2

FDIV

This encoder functions as a controller that controls
the front divergence of the currently selected chan-
nel. Turning the encoder toward the right increases
the value.

This is linked with the knob displayed in the SURR
PRM screen DIVERGENCE area (if the surround
mode = 6.1ch, this will be the F knob).

3

R< >F

This encoder functions as a controller that moves the
position of the currently selected channel between
front and rear.

4

RDIV (6.1ch only)

This encoder functions as a controller that controls
the rear divergence of the currently selected channel.
Turning the encoder toward the right increases the
value.

If the surround mode is 6.1ch, this is linked with the
R knob displayed in the DIVERGENCE area.

5

LFE (5.1ch/6.1ch only)

This encoder controls the send level of the signal sent
from the currently selected channel to the LFE sur-
round bus (MIX bus 24).

Turning the encoder toward the right increases the
value.

If the surround mode is 6.1ch or 5.1ch, this is linked
with the LFE knob displayed in the LFE area of the
SURR PRM screen.

While surround mode is active, the MIX SEND
[LEVEL/PAN] encoders for MIX 17–24 will not
function as conventional send level controllers. Also,
the MIX SEND [NAME] indicators will not display
the MIX bus names.

Instead, the MIX SEND [NAME] indicators will
indicate the names of surround mode functions, and
the MIX SEND [LEVEL/PAN] encoders for MIX 17–
24 will control the functions described in

1

–

5

.

MIX SEND [LEVEL/PAN] encoders to which no
function is assigned will do nothing; their MIX
SEND [NAME] indicators will be dark.

However, the MIX SEND [ON] switches 17–24 will
indicate the on/off status of the send to each MIX bus
as they normally do, and can also be switched on/off.

•

Note that encoders

1

–

4

function as controllers

that control specific surround parameters; they
do not control the send level to the MIX buses.
In contrast, encoder

5

controls the send level to

MIX bus 24 in the usual way.

PAIR

PAIR

PAIR

1

3

2

4

5

«
...
39
40
41
42
43
...
»

Содержание PM1D Manager V2

























































Отзывы:

Нет отзывов

Похожие инструкции для PM1D Manager V2

Powerhead PA Mixer

Бренд: KAM Страницы: 4

Бренд: MegaBeat Audio Страницы: 5

Бренд: Behringer Страницы: 76

Бренд: Omnitronic Страницы: 44

Бренд: YATO Страницы: 92

Бренд: Boss Страницы: 2

Бренд: Parkside Страницы: 55

Бренд: IBM Страницы: 64

SansAmp PSA 2.0

Бренд: tech21 Страницы: 12

Бренд: M-Audio Страницы: 34

Бренд: Shure Страницы: 10

Бренд: LOOPTROTTER Страницы: 9

Бренд: AEG Страницы: 5

Бренд: Hitachi Страницы: 16

Бренд: Braven Страницы: 74

Бренд: Russell Hobbs Страницы: 8

Бренд: PITSOS Страницы: 10

Бренд: Profi Cook Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды