Yamaha PM1D Manager V2 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 56

background image

PM1D System Software V1.6 Supplementary Manual

42

•

MIX SEND [ON] switches 17–24 turn on/off the
signals that are sent from an input channel to the
corresponding surround bus. (Buses not used by
the current surround mode can be operated, but
will make no difference.) These are linked with
the surround bus ON/OFF buttons in the SURR
PRM screen.

•

While a surround mode is active, MIX SEND
[PRE] switches 17–24 cannot be operated (they
are fixed at Post).

•

No audio signal at all will be sent to a MIX bus
17–24 to which the current surround mode does
not assign a signal.

■

MIX OUTPUT block

The MIX [NAME] indicators of MIX channels 17–24 will display the names of the surround channels assigned to the
MIX channels, according to the currently selected surround mode. These names are set automatically when you switch to
surround mode. However, you are free to modify the names afterward.

The encoders of MIX channels 17–24 are used to control the output level of each surround bus.

■

CH to MIX screen

The PAN/ROUTING function CH to MIX screen will
change as follows.

1

Pairing

Pairing for MIX buses 17–24 will be forcibly
defeated; they will function as monaural buses. It is
not possible to pair MIX buses 17–24 while surround
mode is active.

2

VARI/FIX indicator

The VARI/FIX indicator of MIX buses 17–24 will
indicate “SURR.” This setting cannot be changed
while surround mode is active.

3

Send level

The knob and value box indicate the send level of the
signal that is sent from the input channel/ST IN
channel to MIX buses 17–24. This value is calculated
based on the current surround pan settings, and can-
not be changed from this screen.

4

ON/OFF buttons

The ON/OFF buttons for the signals sent from each
input channel to MIX buses 17–24 used for surround
will all be turned on. (However, you may switch
them off afterward.)

These buttons are linked with the surround bus ON/
OFF buttons in the SURR PRM screen, and with
SELECTED INPUT CHANNEL block MIX SEND
[ON] switches 17–24.

5

PRE/POST buttons

All signals sent from each input channel to MIX
buses 17–24 are set to POST (post fader). This set-
ting cannot be changed while surround mode is
active.

•

When you access the JOB SELECT popup win-
dow from the CH to MIX screen, the OK button
will be grayed-out and cannot be clicked if MIX
buses 17–24 are selected.

•

If you copy the send levels to a MIX bus or copy
the MIX bus on/off or pre/post settings while sur-
round mode is active, MIX buses 17–24 will be
excluded from the operation.

PAIR

PAIR

PAIR

ON

ON

ON

ON

ON

ON

ON

ON

PAIR

1
2

3

4
5

«
...
40
41
42
43
44
...
»

Содержание PM1D Manager V2

























































Отзывы:

Нет отзывов

Похожие инструкции для PM1D Manager V2

DANALOG DDX3216

Бренд: Behringer Страницы: 22

Бренд: Omcan Страницы: 12

Бренд: TREVIDEA Страницы: 12

Бренд: PedalPCB Страницы: 5

Бренд: Gorenje Страницы: 47

Dark Waves Tap Tempo Tremolo v2.0

Бренд: Vein-Tap Страницы: 14

Бренд: SoundCraft Страницы: 33

Бренд: Numark Страницы: 12

Бренд: Effectrode Страницы: 4

Бренд: Kogan Страницы: 8

Бренд: Sinbo Страницы: 50

Бренд: Hitachi Страницы: 16

Бренд: Phonic Страницы: 12

Maxi Mix Plus M63210-33

Бренд: Barnstead International Страницы: 16

Бренд: XTline Страницы: 19

Бренд: Pantheon Страницы: 7

Бренд: Altman Страницы: 24

Бренд: Audiodesign Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды