Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя

Страница: 110 / 172

8-18

6. If the engine oil is not between the tip of the

dipstick and the maximum level mark, add
sufficient oil of the recommended type to raise
it to the correct level.

NOTICE:

Be sure the

engine oil is at the correct level, otherwise
engine damage may result.

[ECB00851]

7. Insert the dipstick into the oil filler hole, and

then tighten the engine oil filler cap.

8. Install the panel.

To change the engine oil (with or without oil fil-
ter cartridge replacement)

1. Place the ATV on a level surface.
2. Remove panel E. (See page 8-10.)
3. Start the engine, warm it up for several min-

utes, and then turn it off.

4. Place an oil pan under the engine to collect

the used oil.

5. Remove the engine oil filler cap, and then re-

move the engine oil drain bolt and its gasket to
drain the oil from the crankcase.

1. Engine oil dipstick
2. Maximum level mark

3. Tip of the engine oil dipstick

1. Engine oil drain bolt

2. Gasket

U1CT62E0.book Page 18 Friday, May 11, 2012 9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Похожие инструкции для Grizzly 450 YFM45FGPD

Бренды по названию

Популярные бренды

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя

Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Похожие инструкции для Grizzly 450 YFM45FGPD

Бренды по названию

Популярные бренды