Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя | Manualshive

Страница: 48 / 172

background image

4-18

4

RES

This indicates reserve. With the fuel cock lever in
this position, the fuel reserve is made available.
Turn the fuel cock lever to this position if you run
out of fuel while riding. When this occurs, refuel as
soon as possible and be sure to turn the fuel cock
lever back to “ON”!

EBU18850

Starter (choke) “

”

Starting a cold engine requires a richer air-fuel mix-
ture, which is supplied by the starter (choke).
Move the starter (choke) in direction (a) to turn on
the starter (choke).

Move the starter (choke) in direction (b) to turn off
the starter (choke).
See the “Starting a cold engine” section on page
6-1 for proper operation.

EBU18881

Seat

To remove the seat

Pull the seat lock lever upward and pull up the seat
at the rear.

1. Arrow mark pointing to “RES”

1. Starter (choke) “

”

U1CT62E0.book Page 18 Friday, May 11, 2012 9:03 AM

«
...
46
47
48
49
50
...
»

Содержание Grizzly 450 YFM45FGPD













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grizzly 450 YFM45FGPD

Бренд: Baja motorsports Страницы: 15

WOLVERINE YFM45FXV

Бренд: Yamaha Страницы: 34

BLASTER YFS200S

Бренд: Yamaha Страницы: 46

Бренд: Strongway Страницы: 15

Бренд: X-TREME Страницы: 26

Бренд: TrailMaster Страницы: 7

Бренд: TrailMaster Страницы: 22

Бренд: DINGO Страницы: 179

Бренд: Global Страницы: 11

Бренд: MADER Страницы: 115

Бренд: Dawson Страницы: 6

Бренд: Cold Jet Страницы: 31

Бренд: Yamaha Страницы: 60

WARRIOR YFM350XNC

Бренд: Yamaha Страницы: 167

Бренд: The Handy Страницы: 8

Бренд: The Handy Страницы: 20

Бренд: PLAYKIN Страницы: 70

Бренд: Golfboard Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды