Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя

Страница: 56 / 172

5-2

Front brake

• Check operation. If soft or spongy, have Yamaha dealer bleed hy-

draulic system.

• Check brake pads for wear, and replace if necessary.
• Check brake fluid level in reservoir, and add specified brake fluid to

specified level if necessary.

• Check hydraulic system for leakage. Correct if necessary.

5-3, 8-39, 8-40, 8-41

Rear brake

• Check operation, and correct if necessary.
• Lubricate cables if necessary.
• Check lever and pedal free play, and adjust if necessary.

5-3, 8-39, 8-41

Throttle lever

• Make sure that operation is smooth. Lubricate cable and lever hous-

ing if necessary.

• Check lever free play, and adjust if necessary.

5-4, 8-37

Control cables

• Make sure that operation is smooth. Lubricate if necessary.

8-48

Wheels and tires

• Check wheel condition, and replace if damaged.
• Check tire condition and tread depth. Replace if necessary.
• Check air pressure. Correct if necessary.

5-4

Brake pedal

• Make sure that operation is smooth. Lubricate pedal pivoting point if

necessary.

8-49

Brake levers

• Make sure that operation is smooth. Lubricate lever pivoting points if

necessary.

8-49

Axle boots

• Check for cracks or damage, and replace if necessary.

8-47

Chassis fasteners

• Make sure that all nuts, bolts and screws are properly tightened.

5-7

Instruments, lights and
switches

• Check operation, and correct if necessary.

5-7

ITEM

ROUTINE

PAGE

U1CT62E0.book Page 2 Friday, May 11, 2012 9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Похожие инструкции для Grizzly 450 YFM45FGPD

Бренды по названию

Популярные бренды

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя

Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Похожие инструкции для Grizzly 450 YFM45FGPD

Бренды по названию

Популярные бренды