Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 129 | Manualshive

Страница: 129 / 172

Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 129

8-37

8

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

5. Install the panel.

EBU24047

Adjusting the throttle lever free play

The throttle lever free play should be checked and,
if necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
The throttle lever free play should measure 3.0–
5.0 mm (0.12–0.20 in) as shown. Periodically
check the throttle lever free play and, if necessary,
adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle le-
ver free play.

1. Slide the rubber cover back.
2. Loosen the locknut.
3. To increase the throttle lever free play, turn

the throttle lever free play adjusting bolt in di-
rection (a). To decrease the throttle lever free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U1CT62E0.book Page 37 Friday, May 11, 2012 9:03 AM

«
...
127
128
129
130
131
...
»

Содержание Grizzly 450 YFM45FGPD













































































































































































Отзывы:

Нет отзывов