Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 32

Страница: 32 / 172

4-2

EBU26695

Indicator lights and warning lights

EBU17990

Low-range indicator light “

”

This indicator light comes on when the transmis-
sion is in the low-range position.

EBU17980

High-range indicator light “

”

This indicator light comes on when the transmis-
sion is in the high-range position.

EBU17860

Neutral indicator light “

”

This indicator light comes on when the transmis-
sion is in the neutral position.

1. On-Command differential gear lock indicator light “DIFF.

LOCK”

2. Low-range indicator light “L”
3. High-range indicator light “H”

4. Neutral indicator light “N”

5. Reverse indicator light “R”
6. Park indicator light “P”

7. On-Command four-wheel-drive/differential gear lock

indicator “

”/“

”

8. Coolant temperature warning light “

”

1. Electric Power Steering warning light “EPS” (for EPS

model)

EPS

U1CT62E0.book Page 2 Friday, May 11, 2012 9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя, Страница: 32 / 172

Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы: