Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 121

Страница: 121 / 172

8-29

4. Remove the front carrier and panel B. (See

5. Remove the radiator cap.

6. Remove panel C. (See page 8-10.)
7. Remove the coolant reservoir cap.
8. Disconnect the coolant reservoir hose on the

coolant reservoir side, and then drain the cool-
ant from the coolant reservoir.

9. After draining the coolant, thoroughly flush the

cooling system with clean tap water.

10. Install the coolant drain bolt and its new gas-

ket, and then tighten the bolt to the specified
torque.

11. Connect the coolant reservoir hose.
12. Pour the recommended coolant into the reser-

voir to the maximum level mark, and then in-
stall the reservoir cap.

NOTICE:

Mix

1. Radiator cap

1. Coolant reservoir hose

Tightening torque:

Coolant drain bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

U1CT62E0.book Page 29 Friday, May 11, 2012 9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя, Страница: 121 / 172

Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы: