Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя | Manualshive

Страница: 135 / 172

background image

8-43

8

TIP

If the specified brake lever free play could be ob-
tained as described above, skip steps 3-8.

3. Fully turn the adjusting bolt in direction (a) to

loosen the brake cable.

4. Slide the rubber cover back.

5. Loosen the brake cable adjuster locknut.
6. To increase the brake lever free play, turn the

brake lever free play adjusting nut in direction
(a). To decrease the brake lever free play, turn

the adjusting nut in direction (b).

NOTICE:

Make sure that distance B measures 22
mm (0.87 in) or less. If distance B reaches
22 mm (0.87 in), adjust the brake lever free
play at the brake lever again. If distance A
exceeds 12.7 mm (0.50 in), have a Yamaha
dealer check the vehicle.

[ECB01151]

7. Tighten the brake cable adjuster locknut.
8. Slide the rubber cover to its original position.
9. Tighten the locknut at the brake lever.

Adjusting the brake pedal height

The top of the brake pedal should be positioned
75.0–85.0 mm (2.95–3.35 in) above the footboard
bracket. If the brake pedal height is incorrect, ad-
just it as follows.

1. Rubber cover

2. Distance B

3. Brake cable adjuster locknut
4. Brake lever free play adjusting nut

1

2

3

4

(b)

(a)

U1CT62E0.book Page 43 Friday, May 11, 2012 9:03 AM

«
...
133
134
135
136
137
...
»

Содержание Grizzly 450 YFM45FGPD













































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Grizzly 450 YFM45FGPD

Бренд: CAMSO Страницы: 50

Бренд: Logan Страницы: 28

Бренд: PRONAR Страницы: 132

Бренд: Range Road Страницы: 10

Бренд: Kellfri Страницы: 12

Бренд: Suzuki Страницы: 508

Бренд: Shop fox Страницы: 2

Challenger 300EX

Бренд: TrailMaster Страницы: 19

Бренд: RiMO Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды