Yamaha Grizzly 450 YFM45FGPD Скачать руководство пользователя страница 115

Страница: 115 / 172

8-23

5. Install the drain bolt and its new gasket, and

then tighten the bolt to the specified torque.

6. Refill with the recommended final gear oil to

the brim of the filler hole as shown.

NOTICE:

Be sure no foreign material enters the final
gear case.

[ECB00421]

TIP

If the recommended oil is not available, SAE80W-
90 API GL-5 Hypoid gear oil may be used instead.
However, when using this oil, noise from the final
gear case may occur when applying the rear
brake.

1. Final gear oil drain bolt

2. Gasket

Tightening torque:

Final gear oil drain bolt:

22 Nm (2.2 m·kgf, 16 ft·lbf)

1. Final gear oil filler bolt

2. Gasket

3. Final gear oil
4. Correct oil level

Recommended final gear oil:

See page 10-1.

U1CT62E0.book Page 23 Friday, May 11, 2012 9:03 AM

Содержание Grizzly 450 YFM45FGPD













































































































































































Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы:

Yamaha Grizzly 450 YFM45FGPD, Руководство пользователя, Страница: 115 / 172

Результаты поиска

Содержание Grizzly 450 YFM45FGPD

Отзывы: