manualshive.com logo in svg

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя

Поделиться
Скачать
Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 94

8-17

8

8. Check the final gear case for oil leakage. If oil

is leaking, check for the cause.

9. Install the final gear case guard by installing

the bolts and tightening them to the specified
torque.

EBU23640

Cleaning the air filter element 

The air filter element should be cleaned at the in-
tervals specified in the periodic maintenance and
lubrication chart. Clean the air filter element more
frequently if you are riding in unusually wet or dusty
areas.

NOTE:

There is a check hose at the bottom of the air filter
case. If dust or water collects in this hose, empty
the hose and clean the air filter element and air fil-
ter case.

1. Remove the seat. (See page 4-12.)
2. Remove the air filter case cover by unhooking

the holders.

Tightening torque:

Final gear oil filler bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

Tightening torque:

Final gear case guard bolt:

16 Nm (1.6 m·kgf, 11 ft·lbf)

1. Air filter case check hose

U5WH63E0.book  Page 17  Monday, May 8, 2006  1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды