Yamaha GRIZZLY 350 YFM35GW страница 119 Скачать руководство пользователя

Страница: 119 / 134

8-42

EBU25751

Troubleshooting chart

Check the fuel level in
the fuel tank.

1. Fuel

There is enough fuel.

There is no fuel.

Check the compression.

Supply fuel.

The engine does not start.
Check the compression.

Operate the electric starter.

2. Compression

There is compression.

There is no compression.

Check the ignition.

Have a Yamaha dealer
check the ATV.

Remove the spark plug
and check the electrodes.

3. Ignition

Wipe off with a dry cloth and correct the
spark plug gap, or replace the spark plug.

Have a Yamaha dealer check the ATV.

The engine does not start.
Have a Yamaha dealer
check the ATV.

The engine does not start.
Check the battery.

Operate the electric starter.

4. Battery

The engine turns over
quickly.

The engine turns over
slowly.

The battery is good.

Check the battery lead connections,
and charge the battery if necessary.

Dry

Wet

Open the throttle halfway and operate
the electric starter.

U5WH63E0.book Page 42 Monday, May 8, 2006 1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды