Yamaha GRIZZLY 350 YFM35GW страница 88 Скачать руководство пользователя

Страница: 88 / 134

8-11

2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Wait a few minutes until the oil settles before

checking.

4. Remove the engine oil filler cap, and then

wipe the dipstick off with a clean rag.

5. Insert the dipstick into the filler hole (without

screwing it in), and then remove it again to
check the oil level.

NOTE:

The engine oil should be between the minimum
and maximum level marks.

6. If the engine oil is at or below the minimum

level mark, add sufficient oil of the recom-
mended type to raise it to the correct level.

7. Insert the dipstick into the oil filler hole, and

then tighten the engine oil filler cap.

1. Engine oil filler cap

1. Dipstick
2. Maximum level mark

3. Minimum level mark

U5WH63E0.book Page 11 Monday, May 8, 2006 1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды