Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя | Manualshive

Страница: 32 / 134

background image

4-10

4

NOTE:

If knocking or pinging occurs, use a different brand
of gasoline or higher octane grade.

CAUTION:

ECB00070

Use only unleaded gasoline. The use of leaded
gasoline will cause severe damage to internal
engine parts, such as the valves and piston
rings, as well as to the exhaust system.

WARNING

EWB00310

●

Do not overfill the fuel tank. Fuel expands
when it heats up. If the fuel tank is overfilled,
fuel could spill out due to heat from the en-
gine or the sun.

●

Be careful not to spill fuel, especially on the
engine or exhaust pipe which can cause a
fire and severe injury. Wipe up any spilled
fuel immediately.

●

Do not refuel right after the engine has been
running and is still very hot.

●

Be sure the fuel tank cap is closed securely.

EBU18820

Fuel cock

The fuel cock supplies fuel from the tank to the car-
buretor while also filtering it.
The fuel cock lever positions are explained as fol-
lows and shown in the illustrations.

OFF

With the fuel cock lever in this position, fuel will not
flow. Always turn the fuel cock lever to this position
when the engine is not running.

1. Arrow mark pointing to “OFF”

U5WH63E0.book Page 10 Monday, May 8, 2006 1:25 PM

«
...
30
31
32
33
34
...
»

Содержание GRIZZLY 350 YFM35GW







































































































































Отзывы:

Нет отзывов

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренд: Panasonic Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды