Yamaha GRIZZLY 350 YFM35GW страница 43 Скачать руководство пользователя

Страница: 43 / 134

5-5

Type:

Tubeless

●

The tires should be set to the recommended
pressure:
Recommended tire pressure:

Front:

25.0 kPa (3.6 psi) (0.250 kgf/cm²)

Rear:

25.0 kPa (3.6 psi) (0.250 kgf/cm²)

• Check and adjust tire pressures when the

tires are cold.

• Tire pressures must be equal on both

sides.

• Tire pressure below the minimum speci-

fied could cause the tire to dislodge from
the rim under severe riding conditions.

Minimum tire pressure:

Front:

22.0 kPa (3.2 psi) (0.220 kgf/cm²)

Rear:

22.0 kPa (3.2 psi) (0.220 kgf/cm²)

• Use no more than the following pressures

when seating the tire beads.

Maximum tire seating pressure:

Front:

250 kPa (36 psi) (2.5 kgf/cm²)

Rear:

250 kPa (36 psi) (2.5 kgf/cm²)

Higher pressures and fast inflation may
cause a tire to burst. Inflate the tires very
slowly and carefully.

EBU19820

Measuring the tire pressure

Use the low-pressure tire gauge.

NOTE:

The low-pressure tire gauge is included as stan-
dard equipment. Make two measurements of the
tire pressure and use the second reading. Dust or
dirt in the gauge could cause the first reading to be
incorrect.

U5WH63E0.book Page 5 Monday, May 8, 2006 1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды