Yamaha GRIZZLY 350 YFM35GW страница 48 Скачать руководство пользователя

Страница: 48 / 134

6-3

NOTE:

The engine is warm when it responds normally to
the throttle with the starter (choke) turned off.

EBU20291

Starting a warm engine

Follow the same procedure as for starting a cold
engine, with the exception that the starter (choke)
is not required when the engine is warm. Instead,
start the engine with the throttle slightly open.

EBU20380

Operating the drive select lever and
driving in reverse

CAUTION:

ECB00170

Before shifting, stop the ATV, otherwise the
transmission may be damaged.

Shifting: Forward

1. Bring the ATV to a complete stop.
2. Shift from neutral to forward and vice versa by

moving the drive select lever along the shift
guide.

NOTE:

Make sure that the drive select lever is completely
shifted into position.

3. Open the throttle lever gradually.

Shifting: Reverse

1. Bring the ATV to a complete stop.
2. Apply the brake pedal.

1. Drive select lever

2. F (Forward)

3. N (Neutral)
4. R (Reverse)

U5WH63E0.book Page 3 Monday, May 8, 2006 1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды