Yamaha GRIZZLY 350 YFM35GW Скачать руководство пользователя страница 90

Страница: 90 / 134

8-13

NOTE:

An oil filter wrench is available at a nearby Yamaha
dealer.

6. Apply a thin coat of engine oil to the O-ring of

the new oil filter cartridge.

NOTE:

Make sure that the O-ring is properly seated.

7. Install the new oil filter cartridge with an oil fil-

ter wrench, and then tighten it to the specified
torque with a torque wrench.

8. Install the engine oil drain bolt, and then tight-

en it to the specified torque.

9. Add the specified amount of the recommend-

ed engine oil, and then install and tighten the
engine oil filler cap.

1. O-ring

1. Torque wrench

Tightening torque:

Oil filter cartridge:

17 Nm (1.7 m·kgf, 12 ft·lbf)

Tightening torque:

Engine oil drain bolt:

23 Nm (2.3 m·kgf, 17 ft·lbf)

U5WH63E0.book Page 13 Monday, May 8, 2006 1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя, Страница: 90 / 134

Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы: