Yamaha GRIZZLY 350 YFM35GW страница 89 Скачать руководство пользователя

Страница: 89 / 134

8-12

To change the engine oil (with or without oil fil-
ter cartridge replacement)

1. Place the ATV on a level surface.
2. Start the engine, warm it up for several min-

utes, and then turn it off.

3. Place an oil pan under the engine to collect

the used oil.

4. Remove the engine oil filler cap, and then re-

move the engine oil drain bolt to drain the oil
from the crankcase.

NOTE:

Skip steps 5–7 if the oil filter cartridge is not being
replaced.

5. Remove the oil filter cartridge with an oil filter

wrench.

1. Engine oil drain bolt

1. Oil filter cartridge

1. Oil filter wrench

U5WH63E0.book Page 12 Monday, May 8, 2006 1:25 PM

Содержание GRIZZLY 350 YFM35GW







































































































































Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды

Yamaha GRIZZLY 350 YFM35GW, Руководство пользователя

Результаты поиска

Содержание GRIZZLY 350 YFM35GW

Отзывы:

Похожие инструкции для GRIZZLY 350 YFM35GW

Бренды по названию

Популярные бренды