Yamaha F400A Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 106

background image

Trouble Recovery

93



ETV: Electric throttle valve



DI: Direct injection



ECU: Engine control unit



STRG: Steering



PTT: Power trim and tilt

If a fuse has blown, replace the fuse accord-
ing to the following procedure.
(1) Turn the main switch to the “

” (off)

position.

(2) Remove the fuse box cover.
(3) If the fuse is secured using screws, re-

move the screws, and then remove the
fuse. Install a spare fuse of the proper
amperage, and then tighten the screws.

(4) If the fuse is not secured using screws,

remove the fuse using the fuse puller. In-
stall a spare fuse of the proper amper-
age.

Consult your Yamaha dealer if the new fuse
immediately blows again.

EMU29529

Power trim and tilt will not operate

EWM02331

Never get under the engine while it is tilt-
ed. Severe injury could occur if the out-
board motor accidentally falls.

If the outboard motor cannot be tilted
up/down using the power trim and tilt unit,
e.g. because of a discharged battery or a fail-
ure with the unit itself, the outboard motor
can be tilted manually.
(1) Stop the engine.
(2) Loosen the manual valve screw by turn-

ing it counterclockwise until it stops.

(3) Adjust the outboard motor to a navigable

angle, tighten the manual valve screw
clockwise, and secure the outboard mo-
tor.

EMU47560

Steer-by-wire system will not operate

If the steer-by-wire system does not operate,
the outboard motor can be steered manually.
To steer the outboard motor manually
(1) Remove the clamp bracket cover by re-

moving the bolts.

1. Screw
2. Fuse

1. Fuse puller

1

2

1

1. Manual valve screw

1

U6KNK0E0.book Page 93 Monday, November 7, 2022 10:23 AM

«
...
97
98
99
100
101
...
»

Содержание F400A











































































































Отзывы:

Нет отзывов

Похожие инструкции для F400A

Бренд: QLA Страницы: 18

Бренд: Keithley Страницы: 49

LM-OG-P2 Advanced

Бренд: Badger Meter Страницы: 48

Бренд: Badger Meter Страницы: 24

Бренд: Bahco Страницы: 92

PLATINUM Series

Бренд: Hach Страницы: 64

Бренд: Mahr Страницы: 384

Бренд: Omega Страницы: 74

Бренд: Omega Страницы: 24

Бренд: Sabre Страницы: 13

Бренд: jenway Страницы: 52

Бренд: JENCO Страницы: 13

Бренд: Xtralis Страницы: 13

Бренд: Tektronix Страницы: 124

DT4120 PS Series

Бренд: Datcon Страницы: 92

Бренд: Agilent Technologies Страницы: 198

Бренд: POSEIDON Страницы: 13

Бренд: wtw Страницы: 63

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды