Yamaha F400A Скачать руководство пользователя страница 60

Страница: 60 / 106

Operation

EMU48702

Neutral hold switch operation

To set
(1) Place the control lever in “ ” (neutral).
(2) When the “NEUTRAL HOLD” switch is

pressed, a beep will sound and the LED
will come on.

(3) You can open or close the throttle. This

can also be done when the control lever
is set in reverse.

To release
(1) Place the control lever in “ ” (neutral).
(2) When the “NEUTRAL HOLD” switch is

pressed, a beep will sound and the LED
will go off.

(3) You can perform normal forward or re-

verse operation

EMU48711

Center engine switch operation

TIP:



You cannot operate the starboard control
lever when the single lever switch is acti-
vated.



You must start all the engines to enable the
center engine.

To set
(1) Place the control lever in “ ” (neutral).
(2) When the “CENTER ENGINE” switch is

pressed, a beep will sound and the LED
will come on.

(3) You can operate the center engine by us-

ing the port side control lever.

1. “NEUTRAL HOLD” switch
2. LED

1. “CENTER ENGINE” switch (triple engines)
2. LED

U6KNK0E0.book Page 54 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды