Yamaha F400A Скачать руководство пользователя страница 89

Страница: 89 / 106

Maintenance

(8) Remove the oil filler bolt and O-ring.

(9) Place the outboard motor in a vertical

position. Using a flexible or pressurized
filling device, inject the gear oil into the oil
filler bolt hole.

(10) Put a new O-ring on the oil level plug.

When the gear oil begins to flow out of
the oil level plug hole, insert and tighten
the oil level plug to the specified torque.

TIP:

Apply a light coat of gear oil to the oil level
plug thread and O-ring before installation.

(11) Put a new O-ring on the oil filler bolt. In-

sert and tighten the oil filler bolt to the
specified torque.

TIP:

Apply a light coat of gear oil to the oil filler bolt
thread and O-ring before installation.

(12) Install the cooling water inlet covers on

both sides of the lower unit, and then
tighten the bolts to the specified torque.

EMU29318

Inspecting and replacing anode(s)

Yamaha outboard motors are protected from
corrosion by sacrificial anodes. Inspect the
external anodes periodically. Remove scales

Tightening torque:

2.5 N·m (0.25 kgf·m, 1.8 lb·ft)

1. Oil filler bolt
2. O-ring

Recommended gear oil:

YAMALUBE outboard gear oil or Hyp-
oid gear oil

Recommended gear oil grade:

SAE 80W API GL-5 / SAE 90 API GL-
5

Gear oil quantity:

1.830 L (1.934 US qt, 1.610 Imp.qt)
(FL400ASTU, FL400ASTX,
FL450AVTU, FL450AVTX)
1.950 L (2.061 US qt, 1.716 Imp.qt)
(F400ASTU, F400ASTX, F450AVTU,
F450AVTX)

Tightening torque:

2.5 N·m (0.25 kgf·m, 1.8 lb·ft)

Tightening torque:

2.5 N·m (0.25 kgf·m, 1.8 lb·ft)

Tightening torque:

2.5 N·m (0.25 kgf·m, 1.8 lb·ft)

U6KNK0E0.book Page 83 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды