Yamaha F400A Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 106

background image

Specifications and requirements

13

EWM01581



If the engine starts in gear, the boat can
move suddenly and unexpectedly, pos-
sibly causing a collision or throwing
passengers overboard.



If the engine ever starts in gear, the
start-in-gear protection device is not
working correctly and you should dis-
continue using the outboard. Contact
your Yamaha dealer.

This digital electronic control unit is only
available for the outboard motor which you
have purchased.
Prior to use of the digital electronic control
unit, set it in order to operate your outboard
motor only. Otherwise, it will not be possible
to operate the outboard motor.
Perform setting of the outboard motor and
the digital electronic control unit in the follow-
ing cases.



If a used outboard motor is installed



If the digital electronic control unit is re-
placed



If the ECM (Electronic control module) of
the used outboard motor is replaced



If the ECM (Electronic control module) of
the digital electronic control unit is re-
placed

Consult your Yamaha dealer for setting.

EMU25695

Battery requirements

EMU44881

Battery specifications

For U.S. insular areas

It is necessary to meet only two of the three
specifications (CCA, MCA, and RC) in one of
the following combinations:



CCA/SAE and RC



MCA/ABYC and RC

For Others

The engine cannot be started if battery volt-
age is too low.

EMU36293

Mounting battery

Mount the battery holder securely in a dry,
well-ventilated, vibration-free location in the
boat.

WARNING! Do not put flammable

items, or loose heavy or metal objects in
the same compartment as the battery.
Fire, explosion or sparks could result.

[EWM01821]

Battery cable

The battery cable size and length are critical.
Consult your Yamaha dealer about the bat-
tery cable size and length.

EMU36303

Multiple batteries

To connect multiple batteries, such as for
multiple engine configurations or for an ac-
cessory battery, consult your Yamaha dealer
about battery selection and correct wiring.

Battery isolator

Your outboard motor is capable of charging
an accessory battery separate from the start-
ing battery using an optional isolator lead.

Battery rating (CCA/SAE):

700 A

Battery rating (MCA/ABYC):

900 A

Battery rating (RC/SAE):

170 minutes

Battery rating (CCA/EN):

670 A

Battery rating (20HR/IEC):

110 Ah

U6KNK0E0.book Page 13 Monday, November 7, 2022 10:23 AM

«
...
17
18
19
20
21
...
»

Содержание F400A











































































































Отзывы:

Нет отзывов

Похожие инструкции для F400A

Бренд: Medeli Страницы: 14

Бренд: Accu-Chek Страницы: 12

Бренд: Bacharach Страницы: 60

Бренд: Bacharach Страницы: 4

Бренд: Bacharach Страницы: 17

HYDROMETTE BL Compact TF-IR 2

Бренд: GANN Страницы: 40

Бренд: Gamry Страницы: 16

Бренд: Magnescale Страницы: 8

50KW POWER WEDGE

Бренд: YORKVILLE Страницы: 9

Бренд: YOSensi Страницы: 3

Бренд: Gibson Страницы: 1

Бренд: Olympus Страницы: 2

RP050B-S1/2 Series

Бренд: MST Страницы: 28

Бренд: Eden Страницы: 6

Бренд: Lutron Electronics Страницы: 43

Бренд: Agilent Technologies Страницы: 198

Proline Promag 50H

Бренд: Endress+Hauser Страницы: 52

Бренд: ABQ Industrial Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды