Yamaha F400A Скачать руководство пользователя страница 12

Страница: 12 / 106

General information

CE marking

Outboard motors affixed with this “CE” mark-
ing conform with the directives of;
2006/42/EC, 2014/30/EU, and 2013/53/EU.

UKCA marking

This product is in compliance with the Recre-
ational Craft Regulations 2017, Electromag-
netic Compatibility Regulations 2016 and
Supply of Machinery (Safety) Regulations
2008.

EMU46133

Compliance mark label

Engines affixed with this label conform to the
regulations for each country.
This label is affixed to the clamp bracket or
swivel bracket.

Regulatory Compliance Mark (RCM)

Engines affixed with this mark conform to
certain portion(s) of the Australian Radio
Communications Act.

ICES-002 Compliance Label

Engines affixed with this mark meet all re-
quirements of the Canadian Interference
Causing Equipment Regulations.

1. CE marking location

6EE-43394-90

1521

0026

1. Compliance mark label location

1. Regulatory Compliance Mark (RCM)

1. ICES-002 Compliance Label

ZMU08190

ZMU08191

U6KNK0E0.book Page 6 Monday, November 7, 2022 10:23 AM

Содержание F400A











































































































Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды

Yamaha F400A, Руководство пользователя

Результаты поиска

Содержание F400A

Отзывы:

Похожие инструкции для F400A

Бренды по названию

Популярные бренды