Yamaha F400A Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 106

background image

Trouble Recovery

88

EMU48434

Troubleshooting

This section describes the likely causes and remedies for problems, such as those in the fuel,
compression, and ignition systems, poor starting, and loss of power. Please note that all of
the items in this section may not apply to your model.
If your outboard motor requires repair, bring it to a Yamaha dealer.
If the engine trouble-alert indicator is blinking, consult your Yamaha dealer.

Trouble

Starter will not operate.

Item

Question

Answer

DEC alert indica-
tor

Does the DEC alert indicator come on
in orange?

Have serviced by a Yamaha dealer.

Control lever

Is control lever in gear?

Shift to neutral.

Battery

Is battery capacity low or weak?

Check battery condition. Use battery
of recommended capacity.

Are battery connections corroded or
loose?

Tighten battery cables and clean bat-
tery terminals.

Fuse

Is fuse for starter relay or electric cir-
cuit blown?

Check for cause of electric overload
and repair. Replace fuse with one of
correct amperage.

Starter

Are starter components malfunction-
ing?

Have serviced by a Yamaha dealer.

Trouble

Engine will not start (starter operates).

Item

Question

Answer

Engine shut-off
cord (lanyard)

Is clip on engine shut-off cord (lan-
yard) installed?

Install clip to engine shut-off switch.

Fuel tank

Is fuel tank empty?

Fill tank with clean, fresh fuel.

Fuel

Is fuel contaminated or stale?

Fill tank with clean, fresh fuel.

Fuel filter

Is fuel filter clogged?

Clean or replace fuel filter.

Fuel pump

Is fuel pump malfunctioning?

Have serviced by a Yamaha dealer.

Spark plugs

Are spark plugs fouled or of incorrect
type?

Inspect spark plugs. Clean or replace
with recommended type.

Ignition parts

Are ignition parts malfunctioning?

Have serviced by a Yamaha dealer.

Ignition wiring

Is ignition wiring damaged or poorly
connected?

Inspect wires for breaks and wear.
Have connections tightened and bro-
ken or worn wires replaced by a
Yamaha dealer.

Engine inner parts

Are engine inner parts damaged?

Have serviced by a Yamaha dealer.

U6KNK0E0.book Page 88 Monday, November 7, 2022 10:23 AM

«
...
92
93
94
95
96
...
»

Содержание F400A











































































































Отзывы:

Нет отзывов

Похожие инструкции для F400A

Бренд: Parr Instrument Company Страницы: 130

Бренд: jenway Страницы: 17

Бренд: Omer Страницы: 2

Бренд: Omicron Страницы: 80

Бренд: Eaton Страницы: 53

Бренд: Oceanic Страницы: 75

Бренд: VEE GEE Страницы: 2

Бренд: Waterproof Страницы: 10

Бренд: Ocean Optics Страницы: 43

Бренд: Ocean Technology Systems Страницы: 12

Бренд: Ocean Reef Страницы: 24

Бренд: Yamaha Страницы: 8

ENERGETIQ LDLS EQ-99X

Бренд: Hamamatsu Страницы: 45

Бренд: Genie Страницы: 14

Бренд: Vaisala Страницы: 40

Бренд: ProsKit Страницы: 10

Бренд: TQC Sheen Страницы: 16

Бренд: NCS Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды