Yamaha E25B Скачать руководство пользователя

Страница: 67 / 74

Maintenance

nect the black battery cable to the NEG-
ATIVE (-) terminal.

3. The electrical contacts of the battery and

cables must be clean and properly con-
nected, or the battery will not start the
engine.

EMU29371

Disconnecting the battery

1. Turn off the battery cut-off switch (if

equipped) and main switch.

NOTICE:

they are left on, the electrical system
can be damaged.

[ECM01930]

2. Disconnect the negative cable(s) from

the negative (-) terminal.

NOTICE:

Al-

ways disconnect all negative (-) ca-
bles first to avoid a short circuit and
damage to the electrical system.

[ECM01940]

3. Disconnect the positive cable(s) and re-

move the battery from the boat.

4. Clean, maintain, and store the battery

according to the manufacturer’s instruc-
tions.

1. Red cable
2. Black cable
3. Battery

69R-9-2A-1E0.book 61 ページ２０１０年２月３日　水曜日　午後５時１８分

Содержание E25B











































































Результаты поиска

Содержание E25B

Отзывы:

Похожие инструкции для E25B

Бренды по названию

Популярные бренды

Yamaha E25B, Руководство пользователя

Результаты поиска

Содержание E25B

Отзывы:

Похожие инструкции для E25B

Бренды по названию

Популярные бренды