background image

Table of contents

Installation ....................................... 24

Installation ...................................... 24

Mounting the outboard motor.......... 24
Clamping the outboard motor ......... 25

Operation ......................................... 27

First-time operation ........................ 27

Breaking in engine .......................... 27
Getting to know your boat ............... 27

Checks before starting engine ....... 27

Fuel level......................................... 28
Remove the top cowling.................. 28
Fuel system..................................... 28
Controls........................................... 28
Engine shut-off cord 

(lanyard)........................................ 29

Oil.................................................... 29
Engine............................................. 29
Install top cowling............................ 29
Battery............................................. 30

Filling fuel and engine oil................ 30

Filling fuel for portable tank............. 30
Gasoline and oil mixing 

(100:1) .......................................... 31

Operating engine............................ 32

Sending fuel (portable tank)............ 32
Starting engine................................ 33

Checks after starting engine .......... 38

Cooling water .................................. 38

Warming up engine ........................ 38

Choke start models ......................... 38

Checks after engine warm up ........ 38

Shifting ............................................ 38
Stop switches.................................. 38

Shifting ........................................... 38

Stopping boat ................................. 40

Stopping engine ............................. 40

Procedure ....................................... 40

Trimming outboard motor............... 41

Adjusting trim angle for manual 

tilt models...................................... 42

Adjusting boat trim .......................... 42

Tilting up and down ........................ 43

Procedure for tilting up (manual 

tilt models) .................................... 44

Procedure for tilting down 

(manual tilt models)....................... 45

Shallow water................................. 45

Cruising in shallow water 

(manual tilt models)....................... 45

Cruising in other conditions............ 46

Maintenance .................................... 47

Transporting and storing 

outboard motor ............................ 47

Clamp screw mounting models ....... 47
Storing outboard motor ................... 48
Procedure........................................ 48
Lubrication....................................... 49
Cleaning the outboard motor........... 49
Checking painted surface of 

outboard motor.............................. 49

Periodic maintenance .................... 49

Replacement parts .......................... 50
Severe operating conditions............ 50
Maintenance chart 1........................ 51
Maintenance chart 2........................ 53
Greasing.......................................... 54
Cleaning and adjusting spark 

plug ............................................... 54

Checking fuel filter........................... 55
Inspecting idle speed ...................... 55
Inspecting wiring and 

connectors .................................... 56

Checking propeller .......................... 56
Removing propeller ......................... 57
Installing propeller ........................... 57
Changing gear oil ............................ 58
Cleaning fuel tank ........................... 59
Inspecting and replacing 

anode(s)........................................ 59

Checking battery (for electric 

start models) ................................. 60

Connecting the battery .................... 60
Disconnecting the battery................ 61

Trouble Recovery............................ 62

Troubleshooting ............................. 62

Temporary action in 

emergency ................................... 65

Impact damage ............................... 65
Replacing fuse ................................ 65
Starter will not operate .................... 66

69R-9-2A-1E0.book  2 ページ  2010年2月3日 水曜日 午後5時18分

Содержание E25B











































































Отзывы: