Yamaha E25B Скачать руководство пользователя | Manualshive

Страница: 36 / 74

background image

Operation

30

EMU36582

Battery

Check that the battery is in good condition,
and fully charged. Check that the battery
connections are clean, secure and covered
by insulating covers. The electrical contacts
of the battery and cables must be clean and
properly connected or the battery will not
start the engine.
Refer to the battery manufacturer’s instruc-
tions for checks for your particular battery.

EMU27234

Filling fuel and engine oil

EMU27248

Filling fuel for portable tank

WARNING

EWM01830

●

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

●

Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,
change your clothes.

1. Be sure the engine is stopped.
2. Disconnect the fuel line from the fuel

tank and tighten the air vent screw on
the fuel tank cap.

3. Remove the portable tank from the boat.
4. Be sure you are in a well-ventilated out-

door area, either securely moored or
trailered.

5. Do not smoke and keep away from

sparks, flames, static electric discharge,
or other sources of ignition.

6. If you use a portable container to store

and dispense fuel, use only an approved
GASOLINE container.

7. Touch the fuel nozzle to the filler open-

ing or funnel to help prevent electrostatic
sparks.

8. Fill the fuel tank, but do not overfill.

WARNING! Do not overfill. Otherwise
fuel can expand and overflow if the

ZMU04677

ZMU06621

ZMU02301

69R-9-2A-1E0.book 30 ページ２０１０年２月３日　水曜日　午後５時１８分

«
...
34
35
36
37
38
...
»

Содержание E25B











































































Отзывы:

Нет отзывов

Похожие инструкции для E25B

Бренд: Uctronics Страницы: 27

Бренд: Supermicro Страницы: 2

Бренд: MACHINIST Страницы: 15

Бренд: Biostar Страницы: 54

Бренд: OLIMEX Страницы: 17

Бренд: Diamond Systems Страницы: 112

Бренд: DAQ system Страницы: 52

Бренд: Tadao Страницы: 3

Бренд: Intel Страницы: 74

Бренд: Microchip Technology Страницы: 34

Бренд: Humandata Страницы: 8

Бренд: DFI Страницы: 44

Бренд: VIA Technologies Страницы: 81

Бренд: MSI Страницы: 45

Бренд: Texas Instruments Страницы: 20

Бренд: COX Страницы: 60

Бренд: Supermicro Страницы: 126

Бренд: Gigabyte Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды