Yamaha E25B Скачать руководство пользователя | Manualshive

Страница: 50 / 74

background image

Operation

44

NOTICE

ECM00241

●

Before tilting the outboard motor, stop
the engine by following the procedure
on page 40. Never tilt the outboard mo-
tor while the engine is running. Severe
damage from overheating can result.

●

Do not tilt up the engine by pushing the
tiller handle (if equipped) because this
could break the handle.

EMU2797B

Procedure for tilting up (manual tilt
models)

1. Place the remote control lever / gear

shift lever in neutral.

2. Disconnect the fuel line from the out-

board motor.

3. Place the tilt lock lever (if equipped) in

the release/up position.

4. Pull up the shallow water lever (if

equipped).

5. Hold the rear of the top cowling with one

hand and tilt the engine up fully.

6. Push the tilt support knob into the clamp

bracket. Or the tilt support bar will turn to
the lock position automatically.

NOTICE:

Do not use the tilt support

lever or knob when trailering the
boat. The outboard motor could
shake loose from the tilt support and
fall. If the motor cannot be trailered in
the normal running position, use an
additional support device to secure it
in the tilt position. For more detailed
information, see page 47.

[ECM01641]

N

ZMU02978

N

ZMU03087

ZMU02977

ZMU02979

69R-9-2A-1E0.book 44 ページ２０１０年２月３日　水曜日　午後５時１８分

«
...
48
49
50
51
52
...
»

Содержание E25B











































































Отзывы:

Нет отзывов

Похожие инструкции для E25B

Бренд: Lantronix Страницы: 10

Бренд: DFI Страницы: 8

Бренд: Advantech Страницы: 4

Бренд: IBASE Technology Страницы: 84

Бренд: DFI Страницы: 60

Бренд: DFI Страницы: 120

Бренд: Gigabyte Страницы: 18

Бренд: Analog Devices Страницы: 128

Бренд: IBASE Technology Страницы: 81

i.MX 8M Mini SODIMM SOM

Бренд: iWave Страницы: 16

MIC23031-4YMT EV

Бренд: Micrel Страницы: 8

Бренд: Gigabyte Страницы: 32

ADIS1650 PCBZSeries

Бренд: Analog Devices Страницы: 11

Бренд: EPOX Страницы: 55

TAS5001-5122C2EVM

Бренд: Texas Instruments Страницы: 27

Бренд: Yamaha Страницы: 124

Бренд: Yamaha Страницы: 122

Бренд: Yamaha Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды