Yamaha E25B Скачать руководство пользователя

Страница: 29 / 74

Engine control system

EMU26803

Alert system

NOTICE

ECM00091

Do not continue to operate the engine if a
alert device has activated. Consult your
Yamaha dealer if the problem cannot be
located and corrected.

EMU2681C

Overheat alert

This engine has an overheat-alert device. If
the engine temperature rises too high, the
alert device will activate.

●

The engine speed will automatically de-
crease to about 2000 r/min.

●

The overheat-alert indicator will light or
blink.

●

The buzzer will sound (if equipped on the
tiller handle, remote control box, or main
switch panel).

If the alert system has activated, stop the en-
gine and check the cooling water inlets:

●

Check trim angle to be sure that the cool-
ing water inlet is submerged.

●

Check the cooling water inlet for clogging.

ZMU03025

ZMU03026

69R-9-2A-1E0.book 23 ページ２０１０年２月３日　水曜日　午後５時１８分

Содержание E25B











































































Результаты поиска

Содержание E25B

Отзывы:

Похожие инструкции для E25B

Бренды по названию

Популярные бренды

Yamaha E25B, Руководство пользователя

Результаты поиска

Содержание E25B

Отзывы:

Похожие инструкции для E25B

Бренды по названию

Популярные бренды