Yamaha E25B Скачать руководство пользователя | Manualshive

Страница: 18 / 74

background image

Specifications and requirements

12

top speed, fuel economy, and even engine
life. Yamaha designs and manufactures pro-
pellers for every Yamaha outboard motor
and every application.
Your outboard motor came with a Yamaha
propeller selected to perform well over a
range of applications, but there may be uses
where a different propeller would be more
appropriate.
Your Yamaha dealer can help you select the
right propeller for your boating needs. Select
a propeller that will allow the engine to reach
the middle or upper half of the operating
range at full throttle with the maximum boat-
load. Generally, select a larger pitch propel-
ler for a smaller operating load and a smaller
pitch propeller for a heavier load. If you carry
loads that vary widely, select the propeller
that lets the engine run in the proper range
for your maximum load but remember that
you may need to reduce your throttle setting
to stay within the recommended engine
speed range when carrying lighter loads.
To check the propeller, see page 56.

EMU25770

Start-in-gear protection

Yamaha outboard motors or Yamaha-ap-

proved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started only
when it is in neutral. Always select neutral
before starting the engine.

EMU25651

Engine oil requirements

If the recommended engine oil is not avail-
able, another 2-stroke engine oil with an
NMMA-certified TC-W3 rating may be used.

EMU36360

Fuel requirements

EMU36771

Gasoline

Use a good quality gasoline that meets the
minimum octane rating. If knocking or ping-
ing occurs, use a different brand of gasoline
or premium unleaded fuel. Yamaha re-
comends that you use alcohol-free (see Gas-
ohol) gasoline whenever possible.

NOTICE

ECM01981

●

Do not use leaded gasoline. Leaded
gasoline can seriously damage the en-
gine.

●

Avoid getting water and contaminants
in the fuel tank. Contaminated fuel can
cause poor performance or engine
damage. Use only fresh gasoline that
has been stored in clean containers.

Gasohol

There are two types of gasohol: gasohol con-
taining ethanol (E10) and that containing

1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)

ZMU04605

-

x

1

2 3

Recommended engine oil:

YAMALUBE 2-stroke outboard motor
oil

Recommended gasoline:

Regular unleaded gasoline

69R-9-2A-1E0.book 12 ページ２０１０年２月３日　水曜日　午後５時１８分

«
...
16
17
18
19
20
...
»

Содержание E25B











































































Отзывы:

Нет отзывов

Похожие инструкции для E25B

Industrial NUC-J6412

Бренд: ASROCK Страницы: 2

Бренд: OLIMEX Страницы: 12

MachXO5-NX Development Kit

Бренд: Lattice Semiconductor Страницы: 64

661FX7MJ Series

Бренд: Foxconn Страницы: 81

Бренд: Gigabyte Страницы: 93

Бренд: austriamicrosystems Страницы: 8

TPS628436-7-8EVM-167

Бренд: Texas Instruments Страницы: 15

MAG Z490 TOMAHAWK

Бренд: MSI Страницы: 76

Бренд: IBASE Technology Страницы: 72

Бренд: IDT Страницы: 35

Бренд: Qiyangtech Страницы: 16

Бренд: AIC Страницы: 58

BOOSTXL-DRV8323Rx

Бренд: Texas Instruments Страницы: 28

Бренд: Analog Devices Страницы: 13

Бренд: Gigabyte Страницы: 96

Бренд: Biostar Страницы: 210

Бренд: Cebekit Страницы: 8

Бренд: Intel Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды