Yamaha E25B Скачать руководство пользователя | Manualshive

Страница: 52 / 74

background image

Operation

46

2. Push the tilt lock lever down to the re-

lease position.

3. Slightly tilt the outboard motor up and

pull the shallow water lever toward the
transom.

4. To return the outboard motor to the nor-

mal position, place the remote control le-
ver / gear shift lever in neutral, then
slightly tilt the outboard motor up. Push
the shallow water lever down. Set the tilt
lock lever to the lock position and slowly

tilt the outboard motor down.

EMU28195

Cruising in other conditions

Cruising in salt water

After operating in salt water, flush the cooling
water passages with fresh water to prevent
them from becoming clogged. Also rinse the
outside of the outboard motor with fresh wa-
ter.

Cruising in muddy, turbid, or acidic water

Yamaha strongly recommends that you use
the optional chromium-plated water pump kit
(see page 13) if you use the outboard motor
in acidic water or water with a lot of sediment
in it, such as muddy or turbid (cloudy) water.
After operating in such water, flush the cool-
ing passages with fresh water to prevent cor-
rosion. Also rinse the outside of the outboard
motor with fresh water.

N

ZMU03087

ZMU02984

ZMU02917

69R-9-2A-1E0.book 46 ページ２０１０年２月３日　水曜日　午後５時１８分

«
...
50
51
52
53
54
...
»

Содержание E25B











































































Отзывы:

Нет отзывов

Похожие инструкции для E25B

Бренд: Rabbit Страницы: 144

B85 Anniversary

Бренд: ASROCK Страницы: 148

Бренд: JETWAY Страницы: 56

Бренд: Texas Instruments Страницы: 16

Бренд: Gigabyte Страницы: 87

X58 PLATINUM SLI - Motherboard - ATX

Бренд: MSI Страницы: 74

LCD Programmer Module

Бренд: Xtralis VESDA Страницы: 54

Бренд: ECS Страницы: 92

Бренд: Lite-on Tech Страницы: 49

Бренд: Richtek Страницы: 15

Бренд: ITX SECURITY Страницы: 18

Бренд: Icop Страницы: 31

Бренд: Gigabyte Страницы: 104

Бренд: AOpen Страницы: 8

Бренд: Silicon Laboratories Страницы: 12

Бренд: Biostar Страницы: 36

Бренд: DFI Страницы: 70

Бренд: DFI Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды