Yamaha BANSHEE YFZ350Y Скачать руководство пользователя

Страница: 43 / 142

5-5

EBU19792

Tires

WARNING

EWB00602

Use of improper tires on this ATV, or operation
of this ATV with improper or uneven tire pres-
sure, may cause loss of control, increasing
your risk of accident.
Pay attention to the following.

●

The tires listed below have been approved
by Yamaha Motor Co., Ltd. for this model.
Other tire combinations are not recommend-
ed.

Front:

Manufacturer/model:

DUNLOP/KT851B

Size:

AT21 x 7-10

Type:

Tubeless

Rear:

Manufacturer/model:

DUNLOP/KT877A

Size:

AT20 x 10-9

Type:

Tubeless

●

The tires should be set to the recommended
pressure:

Recommended tire pressure:

Front:

30.0 kPa (0.300 kgf/cm

, 4.4 psi)

Rear:

30.0 kPa (0.300 kgf/cm

, 4.4 psi)

●

Check and adjust tire pressures when the
tires are cold.

●

Tire pressures must be equal on both
sides.

●

Tire pressure below the minimum speci-
fied could cause the tire to dislodge from
the rim under severe riding conditions.

Minimum tire pressure:

Front:

27.0 kPa (0.270 kgf/cm

, 4.0 psi)

Rear:

27.0 kPa (0.270 kgf/cm

, 4.0 psi)

●

Use no more than the following pressures
when seating the tire beads.

Maximum tire seating pressure:

Front:

250 kPa (2.5 kgf/cm

, 36 psi)

Rear:

250 kPa (2.5 kgf/cm

, 36 psi)

Содержание BANSHEE YFZ350Y















































































































































Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды

Yamaha BANSHEE YFZ350Y, Руководство пользователя

Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды