Yamaha BANSHEE YFZ350Y Скачать руководство пользователя страница 117

Страница: 117 / 142

8-42

EBU24880

Lubricating the drive chain

The drive chain must be cleaned and lubricated at
the intervals specified in the periodic maintenance
and lubrication chart, otherwise it will quickly wear
out, especially when riding in dusty or wet areas.
Service the drive chain as follows.

NOTICE

ECB00560

The drive chain must be lubricated after wash-

ing the ATV or riding in the rain.

1. Clean the drive chain with kerosene and a

small soft brush.

NOTICE

ECB00570

To prevent damaging the O-rings, do not clean
the drive chain with steam cleaners, high-pres-

sure washers or inappropriate solvents.

2. Wipe the drive chain dry.
3. Thoroughly lubricate the drive chain with a

special O-ring chain lubricant.

Tightening torques:

Locknut:

16 Nm (1.6 m·kgf, 11 ft·lbf)

Axle holding nut (upper):

120 Nm (12.0 m·kgf, 85 ft·lbf)

Axle holding nut (lower):

60 Nm (6.0 m·kgf, 43 ft·lbf)

1. O-ring

Содержание BANSHEE YFZ350Y















































































































































Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды

Yamaha BANSHEE YFZ350Y, Руководство пользователя

Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды