Yamaha BANSHEE YFZ350Y Скачать руководство пользователя

Страница: 120 / 142

8-45

EBU25032

Lubricating the upper and lower arm
pivots

The upper and lower arm pivots must be lubricated
at the intervals specified in the periodic mainte-
nance and lubrication chart.
Lubricate the pivoting points using a grease gun.

Left side

Right side

EBU25102

Lubricating the steering shaft

The steering shaft must be lubricated at the inter-
vals specified in the periodic maintenance and lu-
brication chart.

EBU26881

Replacing a headlight bulb

If a headlight bulb burns out, replace it as follows.

1. Remove the headlight unit by removing the

Recommended lubricant:

Lithium-soap-based grease

1. Grease nipple

Recommended lubricant:

Lithium-soap-based grease

Содержание BANSHEE YFZ350Y















































































































































Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды

Yamaha BANSHEE YFZ350Y, Руководство пользователя

Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды