Yamaha BANSHEE YFZ350Y Скачать руководство пользователя

Страница: 115 / 142

8-40

rectly, have a Yamaha dealer check the internal

clutch mechanism.

EBU24852

Drive chain slack

The drive chain slack should be checked before
each ride and adjusted if necessary.

To check the drive chain slack

1. Place the ATV on a level surface.

TIP

When checking and adjusting the drive chain
slack, there should be no weight on the ATV and

all tires must be touching the ground.

2. Move the ATV back and forth to locate the

tightest portion of the drive chain, and then
measure the drive chain slack as shown.

3. If the drive chain slack is incorrect, adjust it as

follows.

To adjust the drive chain slack

1. Place the ATV on a level surface.
2. Loosen the axle holding nuts.

Drive chain slack:

12.0–18.0 mm (0.47–0.71 in)

1. Drive chain slack

Содержание BANSHEE YFZ350Y















































































































































Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды

Yamaha BANSHEE YFZ350Y, Руководство пользователя

Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды