manualshive.com logo in svg

Yamaha BANSHEE YFZ350Y, Руководство пользователя, Страница: 114 / 142

Поделиться
Скачать
Yamaha BANSHEE YFZ350Y Скачать руководство пользователя страница 114

 

8-39

 

1

2

3

4

5

6

7

8

9

10

11

 

effect.

Turn the adjusting nut while holding the brake light
switch in place. To make the brake light come on
earlier, turn the adjusting nut in direction (a). To
make the brake light come on later, turn the adjust-
ing nut in direction (b).

 

EBU24810

 

Adjusting the clutch lever free play 

 

The clutch lever free play must be checked and, if
necessary, adjusted at the intervals specified in
the periodic maintenance and lubrication chart.
The clutch lever free play should measure as

shown. If the free play is incorrect, adjust it as fol-
lows.

1. Loosen the locknut at the clutch lever.
2. To increase the clutch lever free play, turn the

adjusting bolt in direction (a), and to decrease
it, turn the bolt in direction (b).

3. Tighten the locknut.

TIP

 

If the specified free play cannot be obtained as de-
scribed above or if the clutch does not operate cor-

 

1.  Brake light switch
2.  Brake light switch adjusting nut

1

2

(a)

(b)

 

1. Locknut
2.  Clutch lever free play adjusting bolt
3.  Clutch lever free play

1

2

3

(a)

(b)

Содержание BANSHEE YFZ350Y















































































































































Отзывы:

Нет отзывов