Yamaha BANSHEE YFZ350Y Скачать руководство пользователя

Страница: 41 / 142

5-3

EBU19550

Fuel and 2-stroke engine oil mixing
ratio

If Yamalube “R” oil is not available, select an oil
from the following list.

NOTICE

ECB00140

Never mix two types of 2-stroke engine oil in
the same batch. Always use the same type of

oil to ensure maximum engine performance.

EBU19580

Transmission oil

Make sure that the transmission oil is at the speci-
fied level. Add oil as necessary. (See page 8-10.)

EBU19630

Coolant

Make sure that the coolant is at the specified level.
Add coolant as necessary. (See page 8-12.)

TIP

The coolant level must be checked on a cold en-
gine since the level varies with engine tempera-

ture.

WARNING

EWB00510

Wait for the engine and radiator to cool before
removing the radiator cap. You could be
burned by hot fluid and steam blown out under
pressure. Always put a thick rag over the cap
when opening. Allow any remaining pressure

to escape before completely removing the cap.

EBU19710

Front and rear brakes

Brake lever and brake pedal

●

Check that there is no free play in the brake le-
ver. If there is free play, have a Yamaha dealer
check the brake system.

●

Check for correct brake pedal height. (See

Recommended 2-stroke engine oil:

Yamalube “R” (Yamalube Racing 2-cycle oil)

Mixing ratio:

24:1

Recommended 2-stroke engine oil

Mixing ratio

Castrol R30

20:1

Castrol A545
Castrol A747

Содержание BANSHEE YFZ350Y















































































































































Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды

Yamaha BANSHEE YFZ350Y, Руководство пользователя

Результаты поиска

Содержание BANSHEE YFZ350Y

Отзывы:

Похожие инструкции для BANSHEE YFZ350Y

Бренды по названию

Популярные бренды