Yaesu FT-818ND Скачать руководство пользователя страница 60

Страница: 60 / 76

Menu Operation

Menu Item 27 [DIG SHIFT]

Function

: Define the carrier frequency offset during DIG (USER-L or USER-U) mode op

eration.

Available Values

: –3000 ~ +3000 Hz

Default

: 0 Hz

Menu Item 28 [EMERGENCY]: USA Version only

Function

: Enable Tx/Rx operation on the Alaska Emergency Channel, 5167.5 kHz.

Available Values

: OFF/ON

Default

: OFF

When this Menu Item is set to “ON,” the spot frequency of 5167.5 kHz will be enabled. To
get to this frequency, use the

knob to navigate; the Alaska Emergency Channel will

be found between the Memory channel “M-PU” and “M-001”.

Use of this frequency is restricted to amateurs operating in (or within 92.6 km of)

the U.S. State of Alaska, and it is to be used for emergency communications only

(involving the immediate protection of life or property).

Menu Item 29 [FM MIC]

Function

: Adjust the microphone gain level for the FM mode.

Available Values

: 0 ~ 100

Default

: 50

Menu Item 30 [FM STEP]

Function

: Select the tuning steps for the

knob on the FM mode.

Available Values

: 5/6.25/10/12.5/15/20/25/50 kHz

Default

: 5 kHz (depends on operating band and transceiver version)

Menu Item 31 [ID]

Function

: Store your callsign into the CW identifier. Up to eight characters may be stored.

The storage procedure is as follows:

1. Press the

knob momentarily to initiate callsign storage (an “under-bar” will

appear below the first character location of the callsign).

2. Rotate the

knob to select the first letter/number of your callsign, then rotate

the

knob one click clockwise to save the first letter/number and move to the

next entry position.

3. Repeat the previous step as many times as necessary to complete your callsign.
4. Press the

knob to save your completed callsign and exit.

Default

: YAESU

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды