Yaesu FT-818ND Скачать руководство пользователя страница 11

Страница: 11 / 76

Installation

SBR-32MH Ni-MH Battery Pack Installation and Use

The supplied

SBR-32MH

Ni-MH Battery Pack provides 9.6 Volts of DC power for your

FT-

818

, with a maximum capacity of 1900 mAh.

Installation

1. To install the

SBR-32MH

Ni-MH Battery

Pack, first remove the battery compart

ment cover, as described previously.

2. Lift out the

FBA-28

battery holder, and

disconnect the short cable connected to
the

FBA-28

, as shown in the illustration.

3. Connect the short cable to the mating

connector on the

SBR-32MH

, and install

the

SBR-32MH

in the battery compart-

ment.

4. Replace the battery compartment cover.

Charging

Charging of the

SBR-32MH

requires the use of either the supplied battery charger (

PA-48B/

C/U

), or an external 13.8 Volt (±15%) DC source. If the battery charger is used, the

FT-818

must be turned off during charging; if an external 13.8 Volt DC source is used (connect-
ed via the supplied

E-DC-6

cable), then you may operate the

FT-818

while charging is in

progress.
1. Turn the

FT-818

off, then connect the supplied battery charger DC connector to the

IN-

PUT: 13.8V

jack on the rear panel of the

FT-818

2. Plug the battery charger into the nearest AC wall outlet.
3. Press the

FT-818

’s

switch for one second to turn the transceiver on.

4. Press the key momentarily.
5. Rotate the

knob so that the function row containing “[CHG, VLT, DSP]” appears

on the display.

6. Press the

key to select the [CHG] option (the display will immediately revert to the

regular frequency display).

7. Turn the

FT-818

off. The display will indicate “CHG TIME RMN”

and remaining time to indicate the time remaining before a full
charge is achieved on the

SBR-32MH

Important Note



The

PA-48

are not designed to power the transceiver for operation (reception or trans-

mission).



Please be advised that the

PA-48

may contribute noise to TV and radio reception in

the immediate vicinity, so we do not recommend its use adjacent to such devices.

FBA-28

SBR-32MH

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды