Yaesu FT-818ND Скачать руководство пользователя страница 39

Страница: 39 / 76

Transmitter Operation

Packet

(

1200/9600 bps FM

)

Operation

The

FT-818

is designed for operation on either 1200 bps or 9600 bps packet, and set-

up is similar to that described previously for SSB-based modes. A separate Data input
adjustment is provided, allowing you to optimize the deviation on the FM Packet modes

separately from the SSB-based Digital modes. The RX-Data output lines are fixed-level

outputs, not affected by the setting of the AF Gain control.
1. Connect your TNC to the

FT-818

’s rear-panel

DATA

jack, per the illustration. Note that

different connections are used for 1200 bps and 9600 bps Packet.

2. Use Menu #40 (PKT RATE) to select the desired Packet mode. Once you have entered

the Menu and have selected Menu #40, rotate the

knob to select either “1200” or

“9600” (bps) as the Packet rate.

3. Press the

key, as needed, to select the PKT mode (the “PKT”

icon will appear on the display).

4. You are now set up for reception on Packet. If you are operating on 1200 bps, try now

to connect to another station or node; you may well find that the drive level needs no

further adjustment.

If you are having trouble connecting due to insufficient or excessive drive from the TNC

to the

FT-818

, use Menu #39 (PKT MIC) to set the drive. Use your terminal software’s

“test” protocol to send out test tones, and adjust the deviation by rotating the

knob, which will vary the data input level to the

FT-818

’s modulator. Remember to press

and hold in the key for one second when adjustments are completed, so as to save
the new setting for Menu #39.

The 9600 bps Packet deviation setting is very critical to successful operation, and it

can only be accomplished using a calibrated deviation meter; the optimum setting

is usually ±2.75 kHz (±0.25 kHz). For 1200 bps, the optimum level is much less criti-

cal, with the optimum deviation being between ±2.5 kHz and ±3.5 kHz.

GND

KEY

DATA

ACC

ANT

INPUT DC13.8V

PTT

DATA IN

GND

DATA

OUT

DATA

PTT

DATA OUT

(1200bps)

OUT

(9600bps)

Pin Label

Note

DATA IN

Maximum Input Lebel:

40 mV pp @1200 bps

1.0 V pp @9600 bps

Impedance: 10 kΩ

PTT

Ground to Transmit

DATA OUT

9600 bps

Maximum Output Level:

500 mVpp

Impedance: 10kΩ

DATA OUT

1200 bps

Maximum Output Level:

300 mVpp

Impedance: 10kΩ

SQL

SQL Open: +5 V

SQL Clised: 0 V

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды