Yaesu FT-818ND Скачать руководство пользователя страница 17

Страница: 17 / 76

Rear Panel Connectors

GND

KEY

DATA

ACC

ANT

INPUT DC13.8V

②

③

⑥

⑤

④

①

INPUT:13.8V

Jack (

)

This is the DC power supply connection for the transceiver, used when operating the

transceiver with an external power supply. Use the supplied DC cable to connect this

jack to the car battery or base station DC power supply, which must be capable of

supplying at least 3A @ 8 - 16 VDC. This jack is also used for battery charging (when

using the supplied

SBR-32MH

battery pack).

GND

Terminal

For best performance and safety, this Ground lug may be connected to a good earth

ground using a short, heavy, braided cable.

KEY

Jack

This 3.5-mm, 3-pin jack

is used for connection to

a CW keyer paddle or a

straight key.

DATA

Jack

This 6-pin, mini-DIN jack accepts AFSK input from a Termi-

nal Node Controller (TNC); it also provides fixed-level Re

ceiver Audio Output, Push-To-Talk (PTT), Squelch Status,

and ground lines.

ACC

Jack

This 8-pin, mini-DIN jack provides a closure to ground

during transmission, ALC, a transmitter-inhibit pin, and

“band data” for connection to an external amplifier. It is also

used for Transceiver-to Transceiver Cloning and for control

of this transceiver using a personal computer.

ANT

Jack

Connect your HF and/or 50 MHz antenna’s 50-ohm coaxial cable to this

-type (“SO-

239”) connector. In its default setting, this jack does not function on 50/144/430 MHz

bands. If you want to enable this jack on 50/144/430 MHz bands, recall and change

the settings of Menu #07.

+13.8V

BAND DATA

ALC

TX INH

RX D

TX D

TX GND

GND

DATA OUT

1200bps

DATA OUT

9600bps

SQL

GND

PTT

DATA IN

KEY

NC GND

GND

When connecting a single straight key

When connecting an electronic keyer paddle

DOT DASH COMMON

DOT DASH

COMMON

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды