Yaesu FT-818ND Скачать руководство пользователя страница 30

Страница: 30 / 76

Transmitter Operation

8. You also can adjust the CW sidetone pitch using Menu #20 (CW PITCH). This adjust-

ment also controls the BFO offset (actual pitch of your transmitted signal relative to your
current receive frequency). To adjust the CW sidetone pitch:



Press and hold in the key for one second to enter the Menu mode.



Rotate the

knob to select Menu #20 (CW PITCH).



Rotate the

knob to select a new pitch tone/BFO offset. The available offset

range is 300 ~ 1000 Hz (default value is “700 Hz”).



When done, press and hold in the key for one second to save the new setting

and exit to normal operation.

Because the CW Pitch corresponds to the actual pitch of your transmitted signal,

the sidetone may be used in a “CW Spot” capacity. Just tune the pitch of the re-

ceived signal to the same pitch as that of your transceiver’s sidetone, and you will

be perfectly “zero beat” with the other station.
The FT-818 can generate a “CW Spot” tone; just press and hold in the

key while

in the CW mode.

Содержание FT-818ND













































































Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды

Yaesu FT-818ND, Руководство по эксплуатации

Результаты поиска

Содержание FT-818ND

Отзывы:

Похожие инструкции для FT-818ND

Бренды по названию

Популярные бренды