Yaesu FT-2000D, Руководство по эксплуатации

Страница: 131 / 140

Page 129 FT-2000D O
PERATING
M
ANUAL
M
ENU
M
ODE
137 tAUd PE2 FRQ
Function : Selects the center frequency of the middle range
for the parametric microphone equalizer when the speech
processor is activated.
Available Values : OFF / 700 ~ 1500 Hz (100 Hz/step)
Default Setting : 800 Hz
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
700 ~ 1500: Center frequencies of 700 Hz ~ 1500 Hz.
You may adjust the equalizer gain and
Q-factor at this selected audio frequency
via menu items “138 tAUd PE2 LVL”
and “139 tAUd PE2 BW.”
138 tAUd PE2 LVL
Function : Adjusts the equalizer gain of the middle range
of the parametric microphone equalizer when the speech
processor is activated.
Available Values : –20 ~ +10
Default Setting : 0
139 tAUd PE2 BW
Function : Adjusts the Q-factor of the middle range of the
parametric microphone equalizer when the speech proces-
sor is activated.
Available Values : 1 ~ 10
Default Setting : 1
140 tAUd PE3 FRQ
Function : Selects the center frequency of the high range
for the parametric microphone equalizer when the speech
processor is activated.
Available Values : OFF / 1500 ~ 3200 Hz (100 Hz/step)
Default Setting : 2100 Hz
OFF: The equalizer gain and Q-factor are set
to factory defaults (flat).
1500 ~ 3200: Center frequencies of 1500 Hz ~ 3200 Hz.
You may adjust the equalizer gain and
Q-factor in this selected audio fre-
quency via menu items “141 tAUd PE3
LVL” and “142 tAUd PE3 BW.”
141 tAUd PE3 LVL
Function : Adjusts the equalizer gain of the high range of
the parametric microphone equalizer when the speech pro-
cessor is activated.
Available Values : –20 ~ +10
Default Setting : 0
142 tAUd PE3 BW
Function : Adjusts the Q-factor of the high range of the
parametric microphone equalizer when the speech proces-
sor is activated.
Available Values : 1 ~ 10
Default Setting : 1
TX GNRL G
ROUP
143 tGEn BIAS
Function : Selects the Final Amplifier’s operation between
the “ Class-A ” and “ Class-AB ” mode, and adjusts the Bias
level while in “Class-A” operation.
Available Values : Ab “Class-AB”/0 ~ 100 “Class-A”
Default Setting : Ab
144 tGEn MAX PWR
Function : Selects a maximum output power limit.
Available Values : 20/50/100/200 W
Default Setting : 200 W
145 tGEn PWRCTRL
Function : Configures the [ RF PWR
] knob.
Available Values : ALL/CAr
Default Setting : ALL
ALL:The [ RF PWR
] knob is enabled on all modes.
CAr: The [ RF PWR
] knob is enabled in all modes
except SSB. In this configuration, the SSB out-
put power will be set to maximum, regardless of
the [
RF PWR
] knob’s position.
146 tGEn ETX-GND
Function : Enables/Disables the
TX GND
jack on the rear
panel.
Available Values : EnA(ENABLE)/diS(DISABLE)
Default Setting : diS(DISABLE)
147 tGEn TUN PWR
Function : Selects a maximum output power limit for driv-
ing the input circuit of an external linear RF amplifier while
tuning (while using the Remote Control function of the
linear RF amplifier).
Available Values : 20/50/100/200 W
Default Setting : 100 W
148 tGEn VOX SEL
Function : Selects the audio input source for triggering
TX during VOX operation.
Available Values : nic / dAtA
Default Setting : nic
nic(MIC): The VOX function will be activated by
microphone audio input.
dAtA(DATA): The VOX function will be activated
by data audio input.
TX AUDIO G
ROUP