Yaesu FT-2000D, Руководство по эксплуатации

Страница: 121 / 140

Page 119 FT-2000D O
PERATING
M
ANUAL
034 GEnE TRACK
Function : Sets the VFO Tracking feature.
Available Values : OFF / bAND / FrEq
Default Setting : OFF
OFF: Disables the VFO Tracking feature.
bAND: When you change bands on the Main (VFO-
A) side, the Sub (VFO-B) band’s VFO will
automatically change to be the same as that of
VFO-A.
FrEq: This function is the almost same as “bAND,”
however, furthermore, the Sub band’s (VFO-
B) frequency changes together with the Main
Band’s (VFO-A) frequency when turning the
Main Dial Tuning knob.
035 GEnE TX TOT
Function : Sets the Time-Out Timer countdown time.
Available Values : OFF / 3 / 5 / 10 / 15 / 20 / 30 min
Default Setting : OFF
The Time-Out Timer shuts off the transmitter after con-
tinuous transmission of the programmed time.
036 GEnE TRV SET
Function : Sets the 10’s and 1’s of the MHz digits display
for operation with a transverter.
Available Values : 30 ~ 49 MHz
Default Setting : 44 MHz
The default setting would be used with a 144 MHz
transverter. If you connect a 430 MHz transverter to the
radio, set this menu to “30” (the “100 MHz” digits are
hidden on this radio).
037 GEnE μ T DIAL
Function : Selects the μ -TUNE mode.
Available Values : StP1 / StP2 / OFF
Default Setting : StP1
StP1: Activates the μ -TUNE system using
“COARSE” steps of the [ VRF
] knob (2 steps/
click) on the 7 MHz and lower amateur bands.
On the 10/14 MHz bands, “FINE” [
VRF
] knob
steps (1 step/click) will be used.
StP2: Activates the μ -TUNE system using “FINE”
steps of the [ VRF
] knob (1 step/click) on the
14 MHz and lower amateur bands on the Main
band (VFO-A).
OFF: Disables the μ -TUNE system. Activates the
VRF feature on the 14 MHz and lower amateur
bands on the main band (VFO-A).
A
DVICE
:
If the optional RF μ Tuning Kit is not connected, this ad-
justment has no effect.
038 GEnE SNB LVL
Function : Adjusts the Sub band (VFO-B) receiver’s IF
Noise Blanker level, when the Noise Blanker is engaged.
Available Values : nAin(MAIN) / 0~100
Default Setting : nAin(MAIN)
When this menu is set to “nAin(MAIN),” you may adjust
the Noise Blanker level using the front panel’s [
NB
] knob.
039 GEnE SUB FIL
Function : Defines the Sub band (VFO-B) receiver’s CW
narrow filter.
Available Values : 1200 / 500 / 300 Hz
Default Setting : 1200 Hz
A
DVICE
:
This Menu item tells the microprocessor which (if any)
optional filter has been installed.
040 GEnE MIC SCN
Function : Enables/disables scanning access via the
microphone’s [
UP
]/[
DWN
] keys.
Available Values : On / OFF
Default Setting : On
041 GEnE SCN RSM
Function : Selects the Scan Resume mode.
Available Values : CAr / 5SEc
Default Setting : 5SEc
CAr: The scanner will hold until the signal disappears,
then will resume after one second.
5SEc: The scanner will hold for five seconds, then re-
sume whether or not the other station is still
transmitting.
042 GEnE ANTIVOX
Function : Adjusts the Anti-VOX Trip Gain which is the
level of negative feedback of receiver audio to the micro-
phone, to prevent receiver audio from activating the trans-
mitter (via the microphone) during VOX operation.
Available Values : 0 ~ 100
Default Setting : 50
043 GEnE FRQ ADJ
Function : Adjusts the reference oscillator.
Available Values : –25 ~ 0 ~ +25
Default Setting : 0
Connect a 50-Ohm dummy load and frequency counter to
the antenna jack; adjust the [
SUB VFO-B
] knob so that
the frequency counter reading is same as the VFO fre-
quency while pressing the
PTT
switch.
A
DVICE
:
Do not perform this Menu item unless you have a high-
performance frequency counter. Perform this Menu item
after aging the transceiver and frequency counter suffi-
ciently (at least 30 minutes).
M
ENU
M
ODE
GENERAL G
ROUP