Yaesu FT-2000D, Руководство по эксплуатации

Страница: 105 / 140

Page 103 FT-2000D O
PERATING
M
ANUAL
M
EMORY
G
ROUPS
Memory channels may be grouped into as many as six convenient batches, for easy identification and selection. For ex-
ample, you might want to set aside memory groups for AM BC stations, shortwave broadcast stations, contest frequencies,
repeater frequencies, and PMS limits, or any other groupings you like.
Each memory group is capable of holding up to 19 or 20 memory channels (the Group size is fixed). When a memory
channel is grouped, the channel numbers change to correspond to the chart below:
Memory Group Assignment
1. Press the [ MENU
] button to enter the Menu mode.
2. Rotate the Main Tuning Dial knob to select Menu item
“ 032 GEnE MEM GRP .”
3. Rotate the [ SUB VFO-B
] knob to set this Menu item
to “
On On
On On
On
” (the default setting is “
OFF OFF
OFF OFF
OFF
”).
4. Press and hold in the [ MENU
] button for two seconds
to save the new setting and exit. Operation will now be
restricted to the six Memory Groups.
To cancel Memory Group operation, repeat steps (1)
through (4) above, choosing “
OFF OFF OFF OFF OFF
” in step (3).
A
DVICE
Note that for the PMS memory group, the PMS memories
“
P-1L P-1L P-1L P-1L P-1L
” through “
P-9U P-9U P-9U P-9U P-9U
” will be so designated, so as to avoid
confusion.
Choosing the Desired Memory Group
You may recall memories just within a particular Memory
Group, if desired.
1. Press the [ V/M
] button, if necessary, to enter the
Memory mode.
2. Press the [ GRP
] button (below and to the left of the
[
SUB VFO-B
] knob). The imbedded LED inside the
switch will light up.
3. Rotate the [ SUB VFO-B
] knob to select the desired
Memory Group.
4. Press the [ M CH
] button (just below the [
GRP
] but-
ton). The imbedded LED inside the switch will light
up.
5. Rotate the [ SUB VFO-B
] knob to select the desired
Memory Channel within the Selected Memory Group.
A
DVICE
:
ˆ If the Red LED imbedded in the [ GRP
] and [
M CH
]
buttons does not light up, check to be sure that the or-
ange lamp to the right of the [
SUB VFO-B
] knob is
not illuminated. If it is, press the [ A/B
] button to make
it go out, then press the [ GRP
] or [
M CH
] button again.
ˆ If no channels have been assigned to a particular
Memory Group, you will not have access to that Group.
G
ROUP
M
EMORY
“OFF”
01 ~ 19
20 ~ 39
40 ~ 59
60 ~ 79
80 ~ 99
P-1L/1U ~ P-9L/9U
M
EMORY
C
HANNEL
N
UMBER
G
ROUP
M
EMORY
“ON”
1-01 ~ 1-19
2-01 ~ 2-20
3-01 ~ 3-20
4-01 ~ 4-20
5-01 ~ 5-20
P-1L/1U ~ P-9L/9U
Main Tuning Dial Knob
[SUB VFO-B] Knob
[MENU] Button
[SUB VFO-B] Knob
[V/M] Button
[GRP] Button
[M CH] Button
[A/B] Button
M
EMORY
O
PERATION