Xycom XVME-212 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 67

background image

XVME-2 12 Manual

August, 1989

2.4.2

Address Space Selection (J3)

The XVME-212

may be placed in VMEbus Short I/O or Standard Memory Space. The

selection is made by configuring Jumper J3 and Switch 8 of Switch Bank Sl (see Figure
2-2) as shown in Table 2-3 below.

Table 2-3. Addressing Options (J3)

Jumper

J3A

J3B

Switch 8 (Sl)

Open
Closed

Option Selected

.

Standard Data Access Operation

Short I/O Access Operation

If Jumper J3A is installed, Switch 8 (on Switch bank Sl) must be set to OPEN.

If Jumper J3B is installed, Switch 8 must be set to CLOSED.

The Standard I/O Architecture recommends that the XVME-212 operate within the Short
I/O Address Space, in order to take advantage of the Standard I/O Architecture’s various

features, which are described in Appendix

A.

If required, the XVME-212

can operate in the Standard Address Space. Note that in this

mode, the XVME-212 will always reside within the upper 64 Kbyte segment of the

Standard Memory Address Space (i.e., the address range FF0000H through FFFFFFH). Sl
switches 1 through 6, then determines which 1K block of the upper 64 Kbyte segment is
to be occupied.

2.4.3

Supervisory/Non-Privileged Mode Selection

The XVME-212 can be configured to respond only to supervisory access, or to both non-
privileged and supervisory accesses, by selecting the position of Switch 7 (located in

Switch Bank Sl, see Figure 2-2), as shown in Table 2-4 below.

Switch 7

Table 2-4. Privilege Options

Privilege Mode Selected

Closed
Open

Supervisory or Non-privileged
Supervisory Only

2.4.4

Address Modifier Reference

Table 2-5 below indicates the actual VMEbus Address Modifier code that the XVME-212

will respond to, based on the position of the options discussed in the previous two
sections.

2-7

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
16
17
18
19
20
...
»

Содержание XVME-212




































































Отзывы:

Нет отзывов

Похожие инструкции для XVME-212

Бренд: Garmin Страницы: 12

Бренд: Handicare Страницы: 56

Бренд: Eaton Страницы: 12

Бренд: Federal Signal Corporation Страницы: 34

Бренд: National Instruments Страницы: 102

Бренд: NAU ROBOTICS Страницы: 109

Maschine Mikro MK2

Бренд: Native Instruments Страницы: 181

FUTERA XLF Series

Бренд: RBI Страницы: 128

Бренд: S&C Страницы: 11

Бренд: S&C Страницы: 24

Бренд: S&C Страницы: 19

Бренд: Saftronics Страницы: 13

Бренд: Yamaha Страницы: 92

Бренд: GEA Страницы: 13

PetroVend PV200

Бренд: OPW Страницы: 2

Бренд: Linak Страницы: 33

LMT070DICFWD-NJN

Бренд: Topway Страницы: 34

Бренд: Burlington Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды