Xycom XVME-212 Скачать руководство пользователя страница 12

Страница: 12 / 67

XVME-212 Manual

August, 1989

Chapter 2

INSTALLATION

2.1 INTRODUCTION

This chapter provides the information needed to configure the XVME-212 and to install
it in a VMEbus backplane card cage.

2.2 SYSTEM REQUIREMENTS

The XVME-212 is a double-high VMEbus compatible module.

To operate, it must be

properly installed in a VMEbus backplane cardcage. The minimum system requirements

for operation of the XVME-212 are one of the following (either A or B below):

A host processor properly installed on the same backplane.

A properly installed controller subsystem. An example of such a control subsystem

is the Xycom XVME-010 System Resource Module.

-OR-

B) A host processor which incorporates an on-board controller subsystem.

2.3 LOCATION OF COMPONENTS RELEVANT TO INSTALLATION

The jumpers, switches, and connectors on the XVME-212 are illustrated in Figure 2-1.

2 - 1

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание XVME-212




































































Результаты поиска

Содержание XVME-212

Отзывы:

Похожие инструкции для XVME-212

Бренды по названию

Популярные бренды

Xycom XVME-212, Руководство пользователя

Результаты поиска

Содержание XVME-212

Отзывы:

Похожие инструкции для XVME-212

Бренды по названию

Популярные бренды