Xycom XVME-212 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 67

background image

XVME-212 Manual

August, 1989

When in the A position, the module cannot respond to interrupts because IACKIN* is not
monitored (IACKIN* is connected directly to IACKOUT* instead). When used in this

configuration, all poles of S2 should be closed to ensure that a programming bug does not
generate VMEbus interrupts.

When interrupts are going to be used, the jumpers must be in the B position.

2.4.7

Debounce Period Jumpers (J4-J 11)

When a mechanical switch closes, several contact bounces can be expected. Several
transitions or quickly changing input images can appear while the switch bounces. To
eliminate these bounces, circuitry is provided, which works as follows. When a change

is detected in an input, the change is not immediately reported to the scanner. Instead,
a timer, with time period, T, will start accumulating time. During this time, T, if the

input reverts to its original state (bounces), the timer is restarted and the change is not
reported. If the input does not bounce for the duration of time, T, the change will be
reported to the scanner at the end of time period T. This means that the input must

assume the new state and stay in the new state without bouncing for time, T, before the
change is reported to the scanner.

The value of time, T, is selectable via eight on-board jumpers. One and onlv one jumper
must be installed. This jumper defines the time, T, to be used by all 32 channels. The
following table shows the available selections.

Table 2-8. Debounce Period Jumpers

install

only

one

Jumper

T min

J l l

3.5 us

Jl0

7 us

J9 14 us

J8 28 us

J 7 112 us
J 5

448 us

J4 1.8 ms

J 6

14 ms

T max

4.5 us

9 us

18 us

36 us

144 us

576 us
2.3 ms

18 ms

Note

One (and only one) of the above jumpers must be

installed for proper module operation.

Note that the time associated with Jll is very short with respect to the opto isolator’s

response time. So selecting this time will essentially defeat the debounce circuitry for
users concerned about speed and not concerned about bounce.

2.5 INSTALLATION

The Xycom VMEbus modules are installed in a standard VMEbus backplane. Figure 2-3

2-9

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
18
19
20
21
22
...
»

Содержание XVME-212




































































Отзывы:

Нет отзывов

Похожие инструкции для XVME-212

Бренд: C.Nord Страницы: 100

CoreBuilder 9000

Бренд: 3Com Страницы: 78

Бренд: Bartlett Страницы: 5

VLT AutomationDrive FC 302

Бренд: Danfoss Страницы: 128

VLT DriveMotor FCP 106

Бренд: Danfoss Страницы: 4

Бренд: Datalogic Страницы: 15

Бренд: Rane Страницы: 2

Бренд: Ebyte Страницы: 35

Бренд: Samson Страницы: 52

Бренд: IDS Страницы: 2

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 3

Бренд: Valcom Страницы: 2

U1000 iQpump Drive

Бренд: YASKAWA Страницы: 26

Z1000 CIMR-ZU*A Series

Бренд: YASKAWA Страницы: 2

Бренд: YASKAWA SIEMENS Страницы: 373

CentriPro Aquavar SOLO

Бренд: Xylem Страницы: 48

Бренд: Penn Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды